86-0755-61696090
Temporary Education Subsidiary And Commercial Occupancy 2-212, Ningbo Engineering College Cui Bai Campus North Gate, Haishu Area, Ningbo, Zhejiang, China (Mainland)
When the upgraded version senses that the animal is approaching, it adds a few seconds of sound and flashes of light, and the burst flash interval is 3-5 seconds. The product uses a digital sensor head to make the sensor more sensitive. Built-in automatic frequency conversion function, drive the animal more powerful, suitable for more small animals.
Solar Ultrasonic Catwalking Dogs Infrared Animals Repller Devices Small Animals Light Drives
Driving range: dog, cat
A. Right in front of 110 ° fan-shaped area, 8 to 10 meters range (the details :see product manuals).
B. Solar panels: 4.8V, 4 section 300 mAh, 2/3AA rechargeable batteries.
C. PIR Sensor :Induction the nearby animals.
D.Light sensor :Indicate the working state.
Principle:
1. Through the solar energy function, energy conservation and environmental protection.
2. Do not damage the wildlife, to protect the environment.
3. Find out this kind of animal fearing or hating the audio frequency and made ultrasonic or send light, herding animals from its scope.
1. Unpack the unit completely and confirm that all parts are present.
2. Connect the repeller head, pole sections, connecting part and ground stake.
3. Turn power switch to “ON” position.
4. The PIR repeller is designed to be left ON continuously. It uses four “AA” size NiCD rechargeable batteries.
5. Once turned ON, the LED light and ultrasonic signal will activate for 15 seconds. Following this activation, the unit will move to stand-by
mode.
6. The unit is now ready for installation. The location should allow adequate sunlight to keep the batteries fully charged. Be sure that the area needing protection is within the effective range of the repeller.
7. For best results, keep the repeller head roughly 9-10 inches above ground.
8. Take care not to stress or break the repeller when installing in hard ground. It is a good idea to prepare the ground for the ground stake to avoid damage to the unit.
9. When the PIR sensor detects motion, the LED light will flash for 3 seconds and the ultrasonic signal will run for 15 seconds. Following this, the repeller will return to stand-by mode.
Specifications:
1. Unit Dimensions: 5-1/2” W x 3-1/2” D x 14-1/3” H.
2. Unit Weight: 8-1/2 ounces.
3. Power Supply: 4 x “AA” NiCD rechargeable batteries.
4. Power Consumption: Standby = 0.8 mAh, working = 15 mAh
5. Ultrasonic Frequency: 18,000-23,000 Hz
6. Coverage Area: 30 feet @ 110° = 2,425 square feet
CAUTION:
(1)Allow the Animal Repeller to operate continuously for best results.
(2)Do not immerse repeller in water.
(3) Do not cover-up the PIR sensor.
(4)To clean the repeller, use a damp-soft cloth and mild soap with water. Do not use harsh chemicals or abrasive cleaning agents that may damage the repeller.
1. Unpack the unit completely and confirm that all parts are present.
2. Connect the repeller head, pole sections, connecting part and ground stake.
3. Turn power switch to “ON” position.
4. The PIR repeller is designed to be left ON continuously. It uses four “AA” size NiCD rechargeable batteries.
5. Once turned ON, the LED light and ultrasonic signal will activate for 15 seconds. Following this activation, the unit will move to stand-by
mode.
6. The unit is now ready for installation. The location should allow adequate sunlight to keep the batteries fully charged. Be sure that the area needing protection is within the effective range of the repeller.
7. For best results, keep the repeller head roughly 9-10 inches above ground.
8. Take care not to stress or break the repeller when installing in hard ground. It is a good idea to prepare the ground for the ground stake to avoid damage to the unit.
9. When the PIR sensor detects motion, the LED light will flash for 3 seconds and the ultrasonic signal will run for 15 seconds. Following this, the repeller will return to stand-by mode.
Specifications:
1. Unit Dimensions: 5-1/2” W x 3-1/2” D x 14-1/3” H.
2. Unit Weight: 8-1/2 ounces.
3. Power Supply: 4 x “AA” NiCD rechargeable batteries.
4. Power Consumption: Standby = 0.8 mAh, working = 15 mAh
5. Ultrasonic Frequency: 18,000-23,000 Hz
6. Coverage Area: 30 feet @ 110° = 2,425 square feet
CAUTION:
(1)Allow the Animal Repeller to operate continuously for best results.
(2)Do not immerse repeller in water.
(3)Do not cover-up the PIR sensor.
(4)To clean the repeller, use a damp-soft cloth and mild soap with water. Do not use harsh chemicals or abrasive cleaning agents that may damage the repeller.
